You are in our US store • Switch to Europe store

Donna Salazar

How to Create a Pennant Set Banner Tutorial by Donna Salazar

Hello everyone! Donna Salazar here with a detailed photo tutorial for you. Today I’m using my Pennant Set to make a cute summery canvas banner.

How to Create a Pennant Set Banner Tutorial by Donna Salazar

I started by punching holes in the top corners of the canvas panels then set eyelets in the holes.

500 CanvasBanner1

I cut a couple strips of Girlie Grunge Gauze for each hole.

500 CanvasBanner2

I thread it through the eyelets and tied a knot then added a Dodz Adhesive Dots Medium on the knots to hold the stick in place.

500 CanvasBanner3

I placed the stick across the knots with adhesive then tied the Girlie Grunge Gauze around the stick.

500 CanvasBanner4

500 CanvasBanner5

500 CanvasBanner6

I showed how to make a die cut mirror image stamped on denim material (Pennant Set) on my blog recently. For instructions on how to achieve this look, click: Mirror Image Stamping Tutorial.

500 DonnaBanner1

I adhered each die cut denim image to the canvas panels using Girlie Grunge Art Medium as well as painted over the top.

500 DonnaBanner2

500 DonnaBanner3

For each flower I die cut 2 of the smaller roses on the Jumbo Rose die. I cut the panel in half and laid it over the smaller rose and leaf then die cut the denim material.

500 DonnaBanner4

I painted the dark side of the die cut flowers with Girlie Grunge Art Medium, lifted each from the surface and used a cotton swab in the center to let the petals hang down while I dried them with a heat gun.

500 DonnaBanner5

500 DonnaBanner6

I painted the leaves with Girlie Grunge Art Medium, lifted them from the surface and dried them with a heat gun.

500 DonnaBanner7

500 DonnaBanner8

I purchased some fancy stamens that came with the little green flower base so I thread the stamen through the flowers, adhered the flower base with Girlie Grunge Art Medium and pressed the flower flat.

500 DonnaBanner9

500 DonnaBanner10

I curled the ends of the stamen with my Spellbinders® Tool ‘n One™ then adhered the flowers and leaves to the center of the 3rd canvas panel using my Dodz Adhesive Dots XL.

500 DonnaBanner11

500 DonnaBanner12

I added another Dodz Adhesive Dots XL under the leaves and then added a flower to the center (made with my Bitty Blossoms and Big Blossom dies from Spellbinders®).

500 DonnaBanner13

500 DonnaBanner14

This is a close up of the finished banner.

500 DonnaBannerClose1

This is a close up of the loop that I made using my Lace Ribbon and Girlie Grunge Art Medium.

500 DonnaBannerClose2

This is a close up of one of the bows that I made using my Lace Ribbon and Girlie Grunge Art Medium and I adhered the bow using my Dodz Adhesive Dots XL. You can also see the Girlie Grunge Gauze and Girlie Grunge Twine behind the bow that was used to tie the sticks at the tops of the panels together.

500 DonnaBannerClose3

The close up below is of the stamped and die cut image. After the Girlie Grunge Art Medium dried I used the Watercolors that I made from my Pigment Powders to add a tiny bit of color and I used a heat gun to make sure the color was set. For instructions on how to create the watercolors, click DIY Watercolor with Pigment Powders Tutorial.

500 DonnaBannerClose4

The close up below is of the flowers on the center panel.

500 DonnaBannerClose5

Product used:
Donna Salazar with Scrapbook Adhesives by 3L®
Girlie Grunge Twine
Girlie Grunge Gauze
Girlie Grunge Art Medium
Dodz Adhesive Dots XL
Pennant Set
Lace Ribbons

Scrapbook Adhesives by 3L®
Dodz Adhesive Dots Medium

Spellbinders® Creative Arts
Jumbo Rose Contour™ Steel Rule Die
Bitty Blossoms
Big Blossom
Flower Bouquet Stamp & Die set
Tool ‘n One™

Clearsnap®
Mix’d Media Inx
Mix’d Media Inx Embossing Powder

Thanks for stopping by!!! Smooches ~D~

Donna Salazar Designs

 

 



One Response to "How to Create a Pennant Set Banner Tutorial by Donna Salazar"

  • Amy Tsuruta