{"id":417,"date":"2010-09-20T10:00:16","date_gmt":"2010-09-20T15:00:16","guid":{"rendered":"http:\/\/www.scrapbook-adhesives.com\/index.php?option=com_wordpress&Itemid=284&lang=en&p=417"},"modified":"2018-10-05T14:42:33","modified_gmt":"2018-10-05T19:42:33","slug":"steampunk-trunk","status":"publish","type":"post","link":"https:\/\/www.scrapbook-adhesives.com\/blog\/2010\/09\/20\/steampunk-trunk\/","title":{"rendered":"Steampunk Trunk Mixed Media Tutorial"},"content":{"rendered":"

As I was digging through my stash recently, I found some little lunch box shaped metal boxes I had bought on clearance, perfect for altering! So I grabbed one of those, some Graphic 45 Steampunk Debutante paper and some bits and baubles in my fun drawer and went to work! These little boxes would work perfectly for gift cards, candy and other small gift items.<\/p>\n

\"Steampunk

Pin This!<\/p><\/div><\/p>\n

Covering the Box<\/h2>\n

The box had red sides, so I covered that with ochre paint.\u00a0 Next I adhered striped paper to the center, and patterned paper to the front and back sides. Crafty Power Tape does a great job of holding paper to metal!\u00a0 Sand the paper so it conforms to the shape of the box.<\/p>\n

\"Steampunk<\/p>\n

 <\/p>\n

The front of the box is a corset, made by die cutting Spellbinders Labels Seventeen die twice, adding eyelets and weaving a ribbon through them.\u00a0 I applied Crafty Power Tape to the back side of the die cuts, adhered to the box and adjusted the ribbon.\u00a0 The metal charm came with its own adhesive; otherwise I would have used Crafty Power tape on that too!<\/p>\n

\"Steampunk<\/p>\n

 <\/p>\n

The back side of the box includes a glass slide, die cuts, plastic letters and a metal key.<\/p>\n

 <\/p>\n

\"Steampunk<\/p>\n

The Glass Slide<\/h2>\n

To make the glass slide, set it on an Adhesive Sheet and burnish it carefully, I used a brayer.\u00a0 Remove it from the backing and position over an image on patterned paper.\u00a0 Burnish again. Trim excess around the glass.<\/p>\n

\"Steampunk<\/p>\n

 <\/p>\n

With an Adhesive Sheet,(1\/4 inch Extreme Double-Sided Tape would also work here) trim strips to \u00bc\u201d width, in 1\u201d and 3\u201d lengths, 2 of each.\u00a0 Carefully peel the yellow off then place the adhesive over the edge of the glass, and wrap it around to the back side.\u00a0 Repeat for each side. \u00a0Burnish carefully!\u00a0 Pour Embossing Powder onto a clean surface (I use a paper plate) and swipe the slide around, covering the adhesive. Heat the embossing powder.\u00a0 (Note: the glass will get hot!)\u00a0 I used a binder clip to hold the glass while heating it.<\/p>\n

 <\/p>\n

\"Steampunk<\/p>\n

 <\/p>\n

Adhere the slide with Crafty Power Tape.\u00a0 Back the patterned paper with an Adhesive Sheet before die cutting, then peel off the backing and apply to the box.\u00a0 Adhere the letter tiles and the flat backed key with Crafty Power Tape.<\/p>\n

On to the Inside!<\/h2>\n

\"Steampunk<\/p>\n

 <\/p>\n

I measured, cut and secured patterned paper to the inside with Crafty Power Tape. Again, I adhered patterned paper to Adhesive Sheets, then cut\/embossed my dies.\u00a0 I applied the clock face to an Adhesive Sheet, then applied the die cut, then a metal arrow, which was secured with a tiny brad.\u00a0 The larger circle die cut features a round metal piece backed with an Adhesive Sheet.\u00a0 The wings are attached with 3D Foam Squares, and the \u201ccreate\u201d came ready to stick.<\/p>\n

 <\/p>\n

\"Steampunk<\/p>\n

 <\/p>\n

The other side of the box features a large flattened bottle cap, die cut circle, radio dial, and plastic button, as well as a tiny glass jar of beads.\u00a0 The bottle cap was flattened in my Wizard Die Cut Machine. I sandwiched the patterned paper in Adhesive Sheets, to make both sides sticky, so it would stick to the clear plastic dial and the metal bottle cap.\u00a0 The back side of the rose button was placed onto an Adhesive Sheet, the positioned onto the dial.<\/p>\n

The tiny glass jar was filled with tiny beads, corked and then adhered to paper, which was then adhered to the \u2018floor\u2019.\u00a0 To make it more secure, I applied 3D Foam Squares to the back side of the jar.<\/p>\n

The fun patterned paper, the trinkets and findings I\u2019ve been collecting and the versatile box came together in this Steampunk inspired box.\u00a0 It could be displayed as a shadow box or used as a gift card holder!\u00a0 I had so much fun piecing this together, and SCRAPBOOK ADHESIVES BY 3L products are strong and versatile, and make altering things so easy!<\/p>\n

Supplies:<\/p>\n