{"id":89544,"date":"2022-07-29T05:00:00","date_gmt":"2022-07-29T10:00:00","guid":{"rendered":"https:\/\/www.scrapbook-adhesives.com\/blog\/?p=89544"},"modified":"2025-11-19T17:56:06","modified_gmt":"2025-11-19T23:56:06","slug":"snowflake-joy-holiday-card","status":"publish","type":"post","link":"https:\/\/www.scrapbook-adhesives.com\/blog\/2022\/07\/29\/snowflake-joy-holiday-card\/","title":{"rendered":"Snowflake JOY Holiday Card"},"content":{"rendered":"

Hello crafty friends! I’m thinking of the holidays in July with this JOY Holiday card featuring the 3D Foam Snowflakes<\/a>. I cut letters J and Y from 3D Foam Creative Sheets Medium White<\/a> and covered them all with heat embossed iridescent ice embossing powder. A simple card design to bring Joy this holiday season!<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Stamp the Background<\/h2>\n

Cut a piece of mint green cardstock to 3.625 x 4.875-inches.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Ink a snowflake stamp with Distress Oxide Weathered Wood ink, stamp once on scrap paper, and then stamp on the background. Repeat with small and large snowflakes to fill the background.<\/p>\n

Apply Ink to Mat<\/h2>\n

Cut a piece of white cardstock to 3.75 x 5-inches and to 1.875 x 3.75-inches<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Apply Distress Oxide Weathered Wood ink along the edges of each piece. Set aside a small piece<\/p>\n

Assemble Card Base<\/h2>\n

Cut a 5.5 x 8.5-inch cream cardstock and fold to make a 4.25 x 5.5-inch card.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Use E-Z Runner\u00ae Petite Permanent Dots Refillable Dispenser<\/a> to apply adhesive to the inked mat piece and fasten it to the card. Repeat to adhere the snowflake background over the mat on the card.<\/p>\n

Cut Letters<\/h2>\n
\n
\"Snowflake<\/figure>\n<\/div>\n

Cut a piece of 3D Foam Creative Sheets Medium White<\/a> large enough for J and Y letter dies. Secure letters to it with removable tape and run through die cutting machine to cut letters. <\/p>\n

Emboss Snowflake and Letters<\/h2>\n
\n
\"Snowflake<\/figure>\n<\/div>\n

Remove the largest snowflake from 3D Foam Snowflakes<\/a> and place it on the non-stick craft mat.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Peel liner from the back of each letter and place next to the snowflake on the craft mat. (Designer Tip: I only used the letter and peeled away the shadow part of each letter)<\/em><\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Peel off top liners from letters and the snowflake, cover with iridescent ice embossing powder, remove excess, and heat with a heat tool to emboss. <\/p>\n

Make JOY Band<\/h2>\n

Cut a piece of mint green paper to 1.75 x 3.75 inches. <\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Secure it to the small piece with the inked edges using E-Z Runner\u00ae Petite Permanent Dots Refillable Dispenser<\/a> to apply adhesive.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Peel the snowflake from the craft mat, place them in the center of the band and place the letters J and Y on either side. Use a ruler to help align letters evenly spaced from the bottom edge.<\/p>\n

Attach the JOY Band<\/h2>\n
\n
\"Snowflake<\/figure>\n<\/div>\n

Place large Thin 3D Foam Squares White Mix<\/a> on the back of the band, peel liners and attach the band to the card front.<\/p>\n

Stamp the Verse<\/h2>\n
\n
\"Snowflake<\/figure>\n<\/div>\n

Stamp verse with Distress Oxide Weathered Wood ink on cream cardstock, cover with clear embossing powder, remove excess, and heat emboss with a heat tool. Trim paper around verse to narrow strip.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Cut 3D Foam Strips<\/a> to fit verse, peel liner, and place on the back of verse. Peel liner from the back and fasten the verse to the card front.<\/p>\n

\n
\"Snowflake<\/figure>\n<\/div>\n

Thanks for Visiting!
Judy Hayes<\/a><\/p>\n

Creative Time:<\/strong> 30 Minutes
Skill Level:<\/strong> Intermediate<\/p>\n

Materials Needed
Scrapbook Adhesives by 3L\u00ae<\/strong> <\/p>\n